Production of secondary raw materials from the hydrotreating of plastic waste pyrolysis oils

Scientific articles | 2026 | REFINE LabInstrumentation
GCxGC, GC/MSD, Pyrolysis, X-ray, ICP-OES, Elemental Analysis
Industries
Energy & Chemicals
Manufacturer
Agilent Technologies, PerkinElmer, LECO

Significance of the topic

The valorization of plastic waste pyrolysis oils (PWPO) addresses two urgent needs: reducing landfill and microplastic pollution from mixed plastic wastes (including waste electrical and electronic equipment, WEEE) and delivering circular, secondary raw materials for the petrochemical and fuel industries. PWPO commonly contains high levels of heteroatoms (Cl, Br, N, S, O), oligomers (e.g., styrene), and a wide boiling-range hydrocarbon matrix that prevents direct reuse in standard refinery or steam-cracking units. Demonstrating that conventional hydrotreating catalysts and refinery-like fractionation can produce halogen-free, petrochemical-grade fractions from highly contaminated PWPO is therefore critical to integrate chemical recycling into existing value chains and to scale sustainable plastics circularity.

Objectives and study overview

This study evaluated continuous hydrotreatment followed by fractional distillation of a laboratory blend of real PWPO derived from mixed waste packaging (WP) plastics, WEEE plastics, and added styrene (target ~15 wt% styrene). Two commercial hydrotreating catalysts (NiMo/γ-Al2O3 and CoMo/γ-Al2O3) were tested in 5-day continuous runs while stepwise increasing temperature (240, 270, 300, 330, 360 °C). The aims were to: (1) determine heteroatom (N, S, Cl, Br, O) removal performance; (2) assess catalyst behavior and deactivation; (3) obtain and characterize distillation cuts (naphtha, kerosene, atmospheric gas-oil (AGO), residue); and (4) evaluate potential material-recycling applications of upgraded fractions beyond fuel use.

Methodology and used instrumentation

The experiments were conducted in a lab-scale co-current fixed-bed hydrotreating unit (tubular reactor, 23 mm ID × 490 mm length) operated at 10 MPa with a PWPO feed rate of 32 g h−1 (WHSV ≈ 1 h−1) and hydrogen flow of 14 L h−1 (H2-to-feed ≈ 400 m3 m−3). Catalyst beds (250–590 µm particles) were diluted 1:2 with SiC to improve heat transfer and avoid channeling; porosity was ≈0.38. Catalysts were dried, in-situ sulfidized using SRGO + DMDS, and stabilized before PWPO feed; 0.15 wt% DMDS was co-fed with PWPO to maintain catalyst sulfidity. Primary liquids and gases were sampled at each temperature step. Primary liquids were fractionated by automated distillation into naphtha (<150 °C), kerosene (150–250 °C), AGO (250–360 °C), and residue (>360 °C).
Used analytical instrumentation and methods (selected):
  • CHN analyzer (LECO CHN TrueSpec) for C/H/N per EN ISO 21663:2021.
  • Trace elemental analyzers (ASTM D5453 for S, D4629 for N).
  • ICP-OES after microwave-induced combustion for Cl and Br (Perkin-Elmer Optima 8000).
  • ED-XRF (Rigaku NEX DE) for metals semi-quantitative analysis.
  • Comprehensive two-dimensional GC (GC×GC-FID/MS, Agilent 8890 with reverse fill-flush modulator) for detailed speciation and PIONA-type grouping (ASTM D8396) and AgNO3/SiO2-based olefin quantification.
  • Preparative liquid chromatography for residue saturates separation.
  • GC (Agilent 6890N) for permanent gases and light hydrocarbons.
  • Stabinger viscometer and density meter (Anton Paar SVM 3000) for kinematic viscosity and density.

Main results and discussion

PWPO feed: density ≈911 kg m−3; composition dominated by aromatics (high styrene content, ~33 wt% in naphtha cut), with notable heteroatom burdens (N ≈7000 mg kg−1, Cl ≈837 mg kg−1, Br ≈346 mg kg−1, S ≈337 mg kg−1) and metals (Si, Mg, Al). Primary distillation of the raw PWPO yielded ca. 49 wt% naphtha, 22 wt% kerosene, 11 wt% AGO and 17 wt% residue. Heteroatom removal and catalyst performance:
  • Both NiMo/Al2O3 and CoMo/Al2O3 demonstrated substantial hydrodehalogenation (HDX), hydrodenitrogenation (HDN) and hydrodesulfurization (HDS) activity. Halogen removal was particularly effective: near-complete elimination of Cl and Br (below detection limit, <5 mg kg−1) was achieved with NiMo at 360 °C and with CoMo by 330 °C (CoMo could not be tested at 360 °C due to reactor outlet solid deposition and pressure rise).
  • NiMo showed superior performance at higher severity (≥330–360 °C), delivering higher hydrogenation capacity (saturation of olefins, hydrogenation of aromatics to some extent) and maximizing light fraction yields via hydrocracking. CoMo exhibited relatively better activity at the lowest temperatures for HDN but was more susceptible to deactivation over time.
  • Catalyst deactivation mechanisms: solid deposition (notably NH4Cl), possible coke formation, and reversible inhibition by HCl/HBr/NH3. DMDS addition helped maintain sulfided active phases but influenced measured S content at lower temperatures.
Fraction yields and quality after hydrotreatment (best-case: NiMo at 360 °C):
  • Naphtha ~48 wt% of PWPO: essentially halogen-free, N and S below quantification (<10 mg kg−1), olefins ≈2 wt%, aromatics dominated (≈75 wt% BTEX), and styrene fully hydrogenated (no styrene detected). This naphtha has high BTEX content, making it a candidate feedstock for solvent-extractive separation and BTX production for petrochemicals.
  • Kerosene ~17 wt%: halogen-free, N ≈86 mg kg−1, S ≈17 mg kg−1, olefins ≈1 wt%, high naphthalene content (~17.6 wt%), not meeting Jet-A1 specs but suitable as an aromatic blendstock (e.g., to reintroduce aromatics into SPK-based sustainable aviation fuel blends) or as a naphthalene-rich feed for commodity chemical production (e.g., phthalic anhydride).
  • AGO ~14 wt%: halogen-free, N ≈571 mg kg−1, S ≈57 mg kg−1, very low olefins (≈0.3 wt%), aromatic-rich with significant naphthalenes and biphenyls; potential feed for BTX production or further refinery hydroprocessing.
  • Residue ~20 wt%: hydrogenation increased saturates fraction at higher temperatures; residue could be blended into heavy fuel blends (marine, heating) or upgraded further (hydrocracking) to increase light product yields.
Key molecular observations: styrene (problematic for instability and gum formation) was completely hydrogenated to ethylbenzene under hydrotreating; olefin content decreased markedly across cuts; non-hydrocarbons (polar heteroatom-containing species) concentrated in intermediate fractions (kerosene) and were effectively reduced by hydrotreatment at higher temperatures.

Benefits and practical applications

  • Demonstrates that conventional, relatively low-cost hydrotreating catalysts (NiMo and CoMo on alumina) can effectively dehalogenate and upgrade even halogen- and bromine-contaminated PWPO from WEEE streams, opening a route to integrate such oils into refinery or petrochemical value chains.
  • Generates a high-BTEX naphtha fraction suitable as a secondary raw material for aromatic extraction (benzene, toluene, ethylbenzene, xylenes) and subsequent polymer feedstock production, supporting circular plastics strategies.
  • Kerosene and AGO fractions are potential feedstocks for specialty chemical processes (naphthalene-derived products like phthalic anhydride) or as aromatic blendstocks to produce SAF when mixed with paraffinic SPK.
  • Residue can be blended into heavy fuel applications or upgraded via hydrocracking/hydroprocessing—providing flexible valorization options depending on market and regulatory constraints.

Limitations and operational considerations

  • Laboratory-scale issues such as solid deposition (likely NH4Cl) at reactor outlets caused pressure rise and prevented CoMo runs at the highest temperature; this phenomenon requires dedicated study for continuous industrial operation.
  • No post-run catalyst characterization (e.g., TEM, XPS, TGA) was reported; thus, deactivation pathways and coke/halide interaction with active sites are not fully quantified.
  • Hydrogen consumption, the need for DMDS sulfidation, and energy for severe conditions are important economic factors to be assessed in techno-economic analyses at scale.

Future trends and potential applications

  • Scale-up studies (pilot/industrial) must address solid salt formation and continuous removal strategies (traps, staged neutralization, optimized feed pretreatment).
  • Detailed catalyst post-mortem studies to design more resilient catalysts (resistant to halide poisoning and salt deposition) or tailored regeneration cycles.
  • Optimization of fractionation cut points to maximize BTEX yield in naphtha and concentrate naphthalenes into a single kerosene/AGO cut for commodity chemical streams.
  • Integration into existing refinery infrastructure (co-processing, dedicated upgrading trains) and development of downstream separation units (e.g., solvent extraction for aromatic recovery) to enable circular supply chains for plastic monomer/feedstock production.
  • Life-cycle assessment and regulatory compliance assessments to quantify environmental benefits and inform policy-driven market incentives for chemically recycled feedstocks.

Conclusion

Hydrotreatment of a real, halogen-rich PWPO blend using conventional NiMo and CoMo hydrotreating catalysts, followed by cut distillation, produced halogen-free fractions with distinct valorization opportunities. The NiMo catalyst at 360 °C yielded the most favorable outcome: an almost halogen-, nitrogen-, and sulfur-free naphtha rich in BTEX (~75 wt%), kerosene and AGO rich in naphthalene derivatives, and a substantial residue fraction. The study demonstrates the technical feasibility of using established hydrotreating technology to convert problematic PWPO streams into secondary raw materials for petrochemical and specialty fuel applications, provided catalyst management, salt formation, and downstream separation are addressed during scale-up.

Used instrumentation

  • Lab-scale fixed-bed hydrotreating unit (co-current tubular reactor, four-zone furnace) — CACTU Solutions setup.
  • LECO CHN TrueSpec analyzer (EN ISO 21663:2021) for C/H/N.
  • Mitsubishi TS-100 trace elemental analyzer (ASTM D5453, D4629) for sulfur and nitrogen.
  • Perkin-Elmer Optima 8000 ICP-OES after microwave-induced combustion for Cl and Br.
  • Rigaku NEX DE ED-XRF for semi-quantitative metal analysis.
  • Agilent 8890 GC×GC-FID/MS (reverse fill-flush modulator) for compositional speciation and PIONA grouping.
  • Preparative liquid column chromatography for residue saturates separation.
  • Agilent 6890N GC for gaseous product analysis.
  • Fischer Technology automatic distillation with Spaltrohr column for fractionation.
  • Anton Paar SVM 3000 Stabinger viscometer for density and kinematic viscosity (ASTM methods).

Reference

Selected references cited in the original article (standard form):
  1. Plastics Europe. The Circular Economy for Plastics. A European Analysis (2024).
  2. X. Shi, Z. Chen, L. Wu, W. Wei, B.J. Ni, Microplastics in municipal solid waste landfills: Detection, formation and potential environmental risks, Curr. Opin. Environ. Sci. Health 31 (2023) 100433.
  3. P. Yuan et al., Overlooked yet critical pathways for microplastics input to soil and groundwater system: transport mechanisms and simulation predictions in landfill environments, Water Res. 284 (2025) 124041.
  4. B. Hegedüs et al., Investigation of gasoline-like transportation fuel obtained by plastic waste pyrolysis and distillation, J. Clean. Prod. 447 (2024) 141500.
  5. M. Laghezza, S. Fiore, F. Berruti, A review on the pyrolytic conversion of plastic waste into fuels and chemicals, J. Anal. Appl. Pyrolysis 179 (2024) 106479.
  6. M. Kusenberg et al., Opportunities and challenges for the application of post-consumer plastic waste pyrolysis oils as steam cracker feedstocks, Waste Manag. 138 (2022) 83–115.
  7. P. Straka et al., Production of transportation fuels via hydrotreating of scrap tires pyrolysis oil, Chem. Eng. J. 460 (2023) 141764.
  8. I. Hita et al., Kinetic Modeling of the Hydrotreating and Hydrocracking Stages for Upgrading Scrap Tires Pyrolysis Oil, Energy Fuels 29 (2015) 7542–7553.
  9. J.G. Speight, Hydrotreating and Hydrocracking Processes in Refining Technology, CRC Press, 2023.
  10. Y. Zhang et al., Techno-economic analysis of two bio-oil upgrading pathways, Chem. Eng. J. 225 (2013) 895–904.
  11. M. Auersvald et al., A comparative study of aromatic content in pyrolysis oils from waste plastics and tires: Assessing common refinery methods, Fuel 369 (2024) 131714.
  12. M. Auersvald et al., Quantitative determination of olefins in pyrolysis oils using selective adsorption by Ag–SiO2 followed by GC×GC-FID, Talanta 281 (2025) 126792.
  13. S. Cañete et al., Continuous hydrogenation of plastic wastes pyrolysis oil over used hydrotreatment catalysts, Catal. Today 454 (2025) 115308.
  14. S. Bezergianni, A. Dimitriadis, Alternative Diesel from Waste Plastics, Energies 10 (2017) 1750.
  15. F. Faisal et al., Upgrading MSW pyrolysis oil through distillation and hydrotreatment for automobile engine applications: A short review, Energy Rep. 9 (2023) 555–560.
  16. B.S. Yoon et al., Upgrading waste plastic pyrolysis oil via hydrotreating over sulfur-treated Ni-Mo/Al2O3 catalysts, Fuel 369 (2024) 131688.
  17. J. Seok et al., Catalytic synergy between Lewis acidic alumina and Pt in hydrodechlorination for plastic chemical recycling, J. Am. Chem. Soc. 146 (2024) 23881–23890.
  18. S. Rodríguez et al., HY zeolite of NiW/HY catalysts for hydroprocessing of a plastic pyrolysis oil/vacuum gas oil blend, J. Anal. Appl. Pyrolysis 186 (2025) 106910.
  19. V.L. Mangesh et al., Hydrotreatment mixed waste plastics to obtain clean transport fuel, J. Clean. Prod. 358 (2022) 131952.
  20. D. Schlehöfer et al., Compatibility of feed for hydrocracking and FCC with scrap tires and waste plastics pyrolysis oil residue, J. Energy Inst. 123 (2025) 102283.

Content was automatically generated from an orignal PDF document using AI and may contain inaccuracies.

Downloadable PDF for viewing
 

Similar PDF

Production of transportation fuels via hydrotreating of scrap tires pyrolysis oil
Upgrading of hydrothermal liquefaction biocrudes from mono- and co-liquefaction of cow manure and wheat straw through hydrotreating and distillation
Advancing circular plastics: hydrotreatment of pyrolysis oils for high-yield ethylene production
A comparative study of aromatic content in pyrolysis oils from waste plastics and tires: Assessing common refinery methods