GC, GCxGC, GC/MSD, GC/SQ
IndustriesEnergy & Chemicals
ManufacturerAgilent Technologies, Thermo Fisher Scientific, LECO
Importance of the topic
The accumulation of end-of-life tires is an environmental and public‑health challenge, while scrap‑tire pyrolysis oil (STPO) represents a carbon‑rich secondary feedstock with potential for conversion to transportation fuels. Upgrading STPO to meet gasoline, jet and diesel specifications can reduce landfill use, recover value from waste, and integrate circularity into refinery operations. Hydrotreating is the key downstream upgrading step to remove heteroatoms, saturate olefins and reduce polyaromatics to make STPO-derived fractions compatible with existing fuel pools.
Objectives and overview of the study
This work evaluated continuous fixed‑bed hydrotreatment of pilot‑scale STPO over a commercial sulfided Ni–Mo/γ‑Al2O3 catalyst to identify operating conditions and processing schemes that yield high‑quality blend components for gasoline, jet and diesel. Experiments explored reaction temperatures 210–360 °C, pressures 6 and 10 MPa, WHSV 1 h−1, and H2/feed ~400 m3·m−3, with time‑on‑stream up to 170 h. Products were distilled into naphtha (≤150 °C), kerosene (150–250 °C), atmospheric gas oil (250–360 °C) and bottom residue (>360 °C) and comprehensively characterized to assess compliance with fuel standards and options for downstream treatment or blending.
Methodology
The STPO feed was obtained from industrial batch pyrolysis of 500 kg scrap tires and analyzed for elemental composition and distillation cuts. The Ni–Mo/γ‑Al2O3 catalyst was dried, sulfided in situ (SRGO + dimethyldisulfide), stabilized with SRGO and then used in a co‑current fixed‑bed reactor (tube reactor, 23 mm ID, 490 mm length). Products were separated in a high‑pressure separator; liquids were redistilled using refinery‑type cuts. Key analytical methods included PIONA (GC/FID) for naphtha composition and octane estimation, preparative liquid chromatography to isolate saturates, GC×GC‑FID for aromatic speciation, GC/MS for saturates speciation, elemental analysis for S, N, H content, simulated distillation (SIMDIST), density and viscosity (Anton Paar), total acid number and CFPP measurements.
Used instrumentation
- Fixed‑bed lab unit (CACTU Solutions) with tubular reactor (23 mm ID × 490 mm length) and six‑point thermowell.
- Commercial sulfided Ni–Mo/γ‑Al2O3 hydrotreating catalyst (crushed, 0.25–0.42 mm fraction, diluted with SiC).
- Agilent 6890N GC‑FID for light gases.
- Agilent GC systems for PIONA and SIMDIST; LECO QuadJet modulated GC×GC‑FID for aromatics/non‑hydrocarbons.
- Thermo GC/MS (Trace Ultra + DSQ II) for saturates speciation.
- Elemental analyzers (Trace Xplorer‑NS for S/N, Elementar vario EL Cube for C content).
- Distillation (Fischer with Spaltrohr column), Anton Paar SVM 3000 for density/viscosity, Callisto 100 for CFPP.
Main results and discussion
- Overall conversion and yields: Primary liquid yields were high (98.7–99.5 wt%). Small C1–C4 gas formation rose with temperature to ≈1.3 wt% at 360 °C/10 MPa. Fraction yields (naphtha, kerosene, gas oil, residue) were only modestly affected by hydrotreating; higher temperatures shifted mass from heavy cuts to lighter fractions.
- Hydrogen consumption: Total H2 uptake increased linearly with temperature and reached ~23.6 g H2·kg−1 STPO at 360 °C/10 MPa. Largest H2 demand was for olefin hydrogenation, followed by aromatic hydrogenation; hydrodesulfurization and hydrodenitrogenation consumed relatively little H2 due to lower atom counts per kg feed.
- Olefins and aromatics: Complete hydrogenation of olefins required ≥330 °C; deeper dearomatization required higher pressure (10 MPa) and higher temperature (≥330–360 °C).
- Desulfurization and denitrogenation: Deep HDS/H DN was achieved at 360 °C/10 MPa with S and N in primary liquids reduced to single‑digit mg·kg−1 (below 10 mg·kg−1).
- Naphtha fraction (C5–150 °C): Origin naphtha had ~26.5 wt% olefins and ~43 wt% aromatics. After hydroprocessing (360 °C/10 MPa) olefins were fully hydrogenated and aromatics reduced to ~33 vol% (≈25% relative dearomatization). Density dropped to ~775 kg·m−3 and S <1 mg·kg−1. Calculated octane was low (~79) due to high cycloalkane content and low branching; thus, naphtha is suitable for refinery gasoline pool blending or catalytic reforming to produce high‑octane reformate/BTEX.
- Kerosene (150–250 °C): STPO kerosene initially contained ~49 wt% aromatics and 39 wt% olefins. Hydrotreating at 270 °C already reduced naphthalenes below the JET‑A1 limit (≤3 vol%). At 360 °C/10 MPa aromatics fell to ~33 wt%, sulfur and nitrogen to low mg·kg−1 levels and calculated smoke point approached specification. Remaining aromatics can be addressed by a mild selective hydrotreatment or by blending (~25 vol%) with HEFA to meet jet fuel aromatics and smoke‑point specs.
- Diesel (150–360 °C): Hydrotreating reduced sulfur to <10 mg·kg−1 at 330–360 °C/10 MPa and N to single‑digit mg·kg−1. However, density remained relatively high and cetane index was low (≈32 at best) because saturates formed are mainly cycloalkanes rather than linear/branched paraffins. Blending with hydrogenated vegetable oil (HVO) containing paraffinic n/iso‑alkanes improved density and viscosity; ~35 wt% HVO was required to raise cetane index to ≥46 (EN 590). CFPP values were excellent (≈−38 to −42 °C), supporting winter/arctic performance.
- Bottom residue (>360 °C): Raw residue was highly aromatic and had high MCR; after hydrotreatment at 360 °C/10 MPa saturates rose (~66.7 wt%), S and N dropped to single‑digit mg·kg−1 and carbon residue became negligible. The upgraded residue is a candidate for very‑low / ultra‑low sulfur bunker fuel or as a feed for co‑hydrocracking.
- Catalyst stability: Over 170 h TOS the commercial Ni–Mo catalyst maintained activity with minor deactivation. Coke deposition occurred but was lower at 10 MPa than 6 MPa; little nitrogen uptake and no measurable sulfur leaching were observed.
Practical benefits and potential uses
- Demonstrated pathway to produce refinery‑compatible distillate cuts from STPO using conventional sulfided hydrotreating catalysts and fixed‑bed equipment.
- Naphtha: can feed catalytic reforming to yield high‑octane gasoline blending stocks and BTEX for petrochemicals.
- Kerosene: with mild additional treatment or blending with HEFA can meet jet fuel specs (ASTM D1655 / D7566 pathways), enabling SAF blending strategies.
- Diesel: blending with paraffinic HVO allows compliance with EN 590, offering a route to low‑temperature‑capable drop‑in diesel blends.
- Residue: upgraded bottom fractions suitable for low‑sulfur marine fuels or as co‑feed for hydrocracking to increase middle‑distillate yields.
Future trends and opportunities
- Catalyst and process optimization: Development of catalysts (e.g., noble metal hydrogenation stages, mixed sulfide/phosphide catalysts, bifunctional supports) tailored for selective dearomatization without excessive cyclization to preserve octane/cetane properties.
- Integrated refinery schemes: Co‑processing STPO with FCC LCO, HVO, or resid streams to dilute problematic components and make use of existing units; further hydrocracking of residues to increase liquid fuels yield.
- Feed pretreatment and pyrolysis optimization: Two‑stage pyrolysis, catalytic pyrolysis or selective removal of sulfur precursors during pyrolysis to reduce downstream H2 demand and improve HDS success.
- Life‑cycle and techno‑economic assessment: Quantify greenhouse gas impact, hydrogen supply logistics, and economics of blending ratios vs. dedicated upgrading steps.
- Scale‑up considerations: Pilot and demonstration co‑processing trials in refinery units to validate catalyst life, contaminant handling and integration costs.
Conclusions
This study shows that STPO can be converted into refinery‑compatible fractions using conventional Ni–Mo/γ‑Al2O3 hydrotreating operated at sufficiently high temperature and pressure (optimal tested case: 360 °C, 10 MPa). Complete olefin saturation, deep desulfurization and denitrogenation, substantial aromatics reduction and improved stability were achieved, producing naphtha, kerosene and diesel components that can enter refinery value chains after modest additional processing or blending (reforming, HEFA/HVO co‑blending). Hydrogen consumption is substantial and scales with severity, and catalyst coke formation is manageable; overall the route is promising for circular valorization of scrap‑tire carbon streams into transportation fuels.
References
- Tire Market: Global Industry Trends, Share, Size, Growth, Opportunity and Forecast 2022-2027, 2022.
- M.S. Senin et al., Analysis of physical properties and mineralogical of pyrolysis tires rubber ash compared natural sand in concrete material, IOP Conf. Ser. Mater. Sci. Eng., 2016.
- S. Ucar et al., Evaluation of two different scrap tires as hydrocarbon source by pyrolysis, Fuel 84 (2005) 1884–1892.
- K. Meardon et al., Scrap tire technology and markets, 1993.
- A. Mohajerani et al., Recycling waste rubber tyres in construction materials, Resources, Conservation Recycling 155 (2020) 104679.
- A.C. Cummins, Global ELT Management–A global state of knowledge, 2019.
- B. Chen et al., Disposal methods for used passenger car tires, Green Energy Environ., 2021.
- C.O. Okoye et al., Manufacturing of carbon black from spent tyre pyrolysis oil–a literature review, J. Clean. Prod. 279 (2021) 123336.
- C.O. Okoye et al., Preparation of carbon black by partial oxidation of spent tyre pyrolysis oil, Waste Manag. 137 (2022) 110–120.
- M. Auersvald et al., Hydrotreatment of straw bio‑oil from ablative fast pyrolysis, Fuel 238 (2019) 98–110.
- H. Yaqoob et al., Potential of tire pyrolysis oil as an alternate fuel for diesel engines: a review, J. Energy Inst., 2021.
- S. Murugan et al., The use of tyre pyrolysis oil in diesel engines, Waste Manag. 28 (2008) 2743–2749.
- R. Pote, R. Patil, Combustion and emission characteristics analysis of waste tyre pyrolysis oil, SN Appl. Sci. 1 (2019).
- J.D. Martínez et al., Fuel properties of tire pyrolysis liquid and its blends with diesel fuel, Energy Fuels 27 (2013) 3296–3305.
- V. Mangesh et al., Prospects of pyrolysis oil from plastic waste as fuel for diesel engines: A review, IOP Conf. Ser. Mater. Sci. Eng., 2017.
- C. Dębek, J. Walendziewski, Hydrorefining of oil from pyrolysis of whole tyres, Fuel 159 (2015) 659–665.
- I. Hita et al., Kinetic modeling of the hydrotreating and hydrocracking stages for upgrading STPO, Energy Fuels 29 (2015) 7542–7553.
- I. Hita et al., Upgrading model compounds and STPO on hydrotreating NiMo catalysts, Fuel 145 (2015) 158–169.
- I. Hita et al., Petcoke‑derived functionalized activated carbon as support for tire oil hydroprocessing, Fuel Process. Technol. 144 (2016) 239–247.
- G.-N. Yun et al., Hydrotreating of Waste Tire Pyrolysis Oil over Ni2P/SBA‑15, Catalysts 11 (2021) 1272.
- N. Jantaraksa et al., Cleaner alternative liquid fuels derived from hydrodesulfurization of waste tire pyrolysis oil, Energy Convers. Manage. 95 (2015) 424–434.
- Q. Zhang et al., Catalytic Hydrodesulfurization of a Spent Tire Pyrolysis Oil Distillate over a Ni–Mo Catalyst, Ind. Eng. Chem. Res. 61 (2022) 1624–1635.
- F. Campuzano et al., On the distillation of waste tire pyrolysis oil: Structural characterization, Fuel 290 (2021) 120041.
- P.T. Williams, R.P. Bottrill, Sulfur‑polyaromatic hydrocarbons in tyre pyrolysis oil, Fuel 74 (1995) 736–742.
- G.-G. Choi et al., Non‑catalytic pyrolysis using a two‑stage pyrolyzer for low sulfur oil, Appl. Energy 170 (2016) 140–147.
- N. Miskolczi et al., Fuels by pyrolysis of waste plastics in a pilot reactor, Fuel Process. Technol. 90 (2009) 1032–1040.
- W. Namchot, S. Jitkarnka, Catalytic pyrolysis of waste tire using HY/MCM‑41, J. Anal. Appl. Pyrolysis 121 (2016) 297–306.
- R. Palos et al., Detailed nature of tire pyrolysis oil blended with light cycle oil, Waste Manag. 128 (2021) 36–44.
- R. Palos et al., Screening hydrotreating catalysts for valorization of LCO/STPO blend, Appl. Catal. B 256 (2019) 117863.
- Y. Han et al., Co‑hydrotreatment of tire pyrolysis oil and vegetable oil, Fuel Process. Technol. 159 (2017) 328–339.
- X.-J. Liu et al., Hydrotreating a waste engine oil and scrap tire oil blend, Fuel 249 (2019) 418–426.
- G. Zhang et al., Properties and utilization of waste tire pyrolysis oil: A mini review, Fuel Process. Technol. 211 (2021) 106582.
- M.S. Abbas‑Abadi et al., Towards full recyclability of end‑of‑life tires: Challenges and opportunities, J. Clean. Prod. (2022).
- P. Straka, D. Maxa, M. Staš, A novel method for separation of high‑molecular‑weight saturates, Org. Geochem. 128 (2019) 63–70.
- P. Straka et al., Effect of reaction conditions on Co‑hydrotreating rapeseed oil and petroleum middle distillates, Catalysts 11 (2021) 442.
- H. Kittel et al., Kerosene from hydrocracking for JET fuel with reduced aromatic content, Petroleum Sci. Technol. (2022).
- K. Januszewicz et al., Waste tyres pyrolysis for obtaining limonene, Materials 13 (2020) 1359.
- N. Mkhize et al., Effect of temperature and heating rate on limonene from waste tyre pyrolysis, J. Anal. Appl. Pyrolysis 120 (2016) 314–320.
- J. Wang et al., Converting polyisoprene rubbers into bio‑jet fuels via hydropyrolysis and vapor‑phase hydrogenation, Energy Convers. Manage. 270 (2022) 116250.
- M.R. Islam et al., Valorization of Solid Tire Wastes by Thermal Treatment, WasteSafe/KUET (2011).
Content was automatically generated from an orignal PDF document using AI and may contain inaccuracies.