GC, GCxGC, Pyrolysis
IndustriesEnergy & Chemicals
ManufacturerAgilent Technologies
Significance of the topic
The global accumulation of mixed post-consumer plastic waste (MPW) presents urgent environmental and circular-economy challenges. Mechanical recycling is limited to clean, well-sorted streams and typically results in downcycling. Thermochemical routes—specifically pyrolysis followed by steam cracking—offer a pathway to return polyolefin-rich waste to virgin-grade olefins (ethylene, propylene). However, crude pyrolysis oils (Py-oils) from real MPW are compositionally complex and contain high olefin/aromatic fractions and heteroatom contaminants (N, O, Cl, metals) that compromise steam cracker operation by increasing coke, fouling, corrosion, and off-spec product formation. Hydrotreatment (HDT) is a refinery-proven catalytic upgrade that can saturate olefins/aromatics and remove heteroatoms, potentially producing cracker-ready feedstocks and enabling integration of waste-derived streams into existing petrochemical infrastructure.Objectives and study overview
The study aimed to evaluate hydrotreatment as an upgrading step for a vacuum-distilled diesel-range fraction of real MPW-derived pyrolysis oil and to quantify the impact of this upgrading on steam-cracking performance. Key goals were to (i) characterize raw and hydrotreated diesel-range Py-oils using comprehensive two-dimensional gas chromatography (GC×GC) and heteroatom-specific detectors, (ii) assess contaminant removal and changes in hydrocarbon matrix, and (iii) benchmark steam-cracking performance of 25 wt% Py-diesel/fossil-naphtha blends (raw and hydrotreated) against fossil naphtha at multiple cracking severities in a bench-scale steam cracker.Used instrumentation
- Hydrotreatment: 250 mL stainless-steel Robinson–Mahoney continuous stirred-tank reactor (CSTR) capable to 120 bar, 400 °C (Autoclave Engineers).
- Catalyst: commercial NiMo/γ-Al2O3 hydrotreatment catalyst.
- Chromatography and detectors: comprehensive two-dimensional GC (Agilent 8890 GC system) with FID for hydrocarbon PIONA analysis, NCD for nitrogen species, AED (Atomic Emission Detector) for oxygen and chlorine; Ag–SiO2 (AgNO3/SiO2) selective adsorption for olefin quantification.
- Online cracking effluent analysis: custom heated valve sampling coupled to three gas chromatographs; refinery gas analyzer (RGA) with TCD for H2/CO/CO2 and FID for C1–C4; GC×GC-FID for C5+ quantification.
- Bench-scale steam cracker (BSSC): Incoloy 800HT reactor tube (1.475 m length, 6 mm ID), Coriolis-controlled pumps, preheating/mixing zones at 350 °C.
- Other analytics: Mettler Toledo DA-100 M density meter; mass balance closure within ±5 wt%.
Methodology
- Feedstock: Real, highly mixed municipal plastic waste dominated by polyolefins (PE, PP) with contamination from PS, PET, EVOH, EVA, PVC, PUR, and PA. Crude Py-oil produced in a pilot pyrolysis unit; vacuum distilled to isolate a diesel-range fraction (C9–C25, IBP–FBP ~136–425 °C).
- Hydrotreatment: liquid-phase CSTR hydrotreatment targeting olefin saturation; conditions: 330 °C, 70 bar, WHSV = 5.76 kgfeed·h−1·kgcat−1, H2/HC = 866.7 Nm3·m−3, NiMo/γ-Al2O3 catalyst. Distillation prior to HDT removed metals and high-boiling contaminants to protect the catalyst.
- Blending and cracking: blends prepared at 25 wt% Py-diesel (raw or HDT) with 75 wt% fossil naphtha; pure fossil naphtha used as benchmark. Steam-cracking conditions: liquid feed 150 g·h−1, steam/HC mass ratio 0.5, coil inlet temperature (CIT) 550 °C, coil outlet temperatures (COT) tested: 820, 850, 880 °C; coil outlet pressure 1.7 bar. Online sampling and comprehensive product analysis (C1–C4, C5–C9 pygas, C10+ pyrolysis fuel oil (PFO)).
- Analytical approach: GC×GC-FID for PIONA and carbon-number distribution; Ag–SiO2 selective adsorption to quantify olefins; GC×GC-NCD for nitrogen, GC×GC-AED for oxygen and chlorine; RGA/TCD for light gases. Mass balances targeted ±5 wt% closure.
Main results and discussion
- Hydrotreatment compositional effects:
- Olefins fell dramatically from ~50.8 wt% (Py-diesel raw: α-olefins 28.2 wt%, iso-olefins 16.8 wt%, diolefins 5.8 wt%) to ~8.4 wt% after HDT (α-olefins 3.3 wt%, iso-olefins 4.8 wt%, diolefins 0.3 wt%).
- Nitrogen reduced from ~1159–1546 mg·kg−1 (depending on sample definition in paper) to <10 mg·kg−1 after HDT; oxygen (initial ~1776 mg·kg−1) became undetectable; chlorine low already (~5 mg·kg−1) and tolerable after blending.
- Hydrogen-to-carbon (H/C) ratio increased from 1.98 to 2.03 after HDT; paraffinic content rose (paraffins: 22.3 → 41.7 wt%; iso-paraffins increased to 24.2 wt%); naphthenes increased due to hydrogenation of aromatics; slight increase in diaromatics attributed to condensation/polymerization under HDT conditions.
- Feedstock specification implications:
- Blending raw Py-diesel 1:3 with fossil naphtha reduced but did not meet industrial thresholds: nitrogen and oxygen remained >100 mg·kg−1 and olefins ≈13 wt% (thresholds ~100 mg·kg−1 for N/O and 2 wt% for olefins for light cracker feeds).
- Hydrotreatment enabled compliance for nitrogen and oxygen (HDT Py-diesel <10 mg·kg−1 N and no detectable O); olefins remained limiting: acceptable blend ratio with fossil naphtha up to ~1:3 to stay below 2 wt% olefins; otherwise further HDT or dilution required.
- Steam cracking performance:
- At all tested severities (COT 820/850/880 °C) 25 wt% Py-diesel blends produced higher ethylene yields than pure fossil naphtha; hydrotreatment further increased ethylene yields and reduced CO and BTX formation.
- Maximum ethylene yield observed for the 25 wt% HDT blend: 31.7 wt% at 880 °C, compared with 29.6 wt% for pure fossil naphtha at identical conditions — an industrially significant improvement (~2 wt% absolute) given large cracker throughputs.
- Extrapolated yields suggest pure HDT Py-diesel could give ~38.2 wt% ethylene vs ~36.6 wt% for raw Py-diesel (extrapolation from blend results reported in the article).
- HDT reduced pygas and BTX yields (aromatic precursors), consistent with lowered olefin/diene content; CO formation (from oxygenates) decreased after HDT.
- PFO (C10+) yields remained higher for pyrolysis-derived blends than for fossil naphtha, driven by heavy C10+ aromatics and naphthenes that are less volatile and more coke-prone; fractional distillation reduced heavy-product formation compared with full-range Py-oil but heavy residues still represent an operational risk (fouling, coke).
- Catalyst and operational observations:
- No significant hydrotreatment catalyst deactivation observed under the short time-on-stream conditions used; prior distillation removed metals and high-boiling contaminants that cause catalyst poisoning. Full-range Py-oils would likely accelerate deactivation without guard beds or pre-filtration.
Benefits and practical applications
- Hydrotreatment converts difficult-to-recycle MPW-derived diesel fractions into cracker-acceptable feedstocks by removing heteroatoms and saturating olefins, enabling co-feeding to existing steam crackers with limited process changes.
- Improved ethylene yield and reduced formation of CO and BTX increase the commercial value and lower downstream purification burdens; even modest absolute increases in ethylene yield (≈2 wt%) are economically significant at industrial scale.
- Combination of distillation, HDT, and blending represents a realistic process train to integrate waste-derived oils into petrochemical value chains while protecting furnace integrity and downstream catalysts.
- Hydrotreatment also reduces COx formation during cracking (less oxygenates), which benefits downstream catalytic units and reduces undesired gaseous by-products.
Future trends and potential applications
- Process integration: coupling hydrotreatment with hydrocracking could process full-range Py-oils directly, convert heavy aromatics into lighter paraffins, reduce the need for fractional distillation, and increase overall liquid yields. Ongoing research focuses on such integration and on kinetic/process modeling for industrial scale-up.
- Pre-treatment advances: depth filtration and low-cost guard beds to remove metals and particulates before hydroprocessing can extend catalyst life and enable treatment of more contaminated feeds.
- Hydrogen sourcing and GHG mitigation: use of low-carbon or renewable hydrogen is crucial to keep the cradle-to-gate carbon footprint favorable compared with incineration; life-cycle assessments integrating hydrogen demand, yields, and energy use are required.
- Catalyst and reactor development: testing hydrotreatment catalysts under industrially relevant fixed-bed (PFR) conditions and developing robust catalysts tolerant to MPW impurities will be necessary for scale-up.
- Fouling management: dedicated fouling assessment (FAST) campaigns and tailored furnace operation strategies will be needed to manage heavy-aromatic-derived deposits and maintain run lengths.
- Catalytic pyrolysis and tailored pyrolysis (to increase light hydrocarbon yield) and downstream upgrading (FCC, delayed coking, lubricant production) are complementary strategies to maximize carbon recovery.
Conclusion
Hydrotreatment of a vacuum-distilled diesel-range fraction from real mixed plastic waste substantially improved feed quality by saturating olefins, hydrogenating aromatics, and removing nitrogen and oxygen. These compositional changes moved the product toward industrial feedstock specifications and translated into improved steam-cracking behavior: higher ethylene yields (25 wt% HDT blend produced up to 31.7 wt% ethylene at 880 °C), reduced CO and BTX formation, and better alignment with cracker feed design. Remaining challenges include heavy C10+ aromatics/naphthenes that drive PFO and fouling risks and the hydrogen/energy demands of hydrotreatment. The integrated route—fractionation, hydrotreatment, blending and potentially hydrocracking—constitutes a viable pathway to valorize hard-to-recycle plastic waste into olefins and supports circular-plastics strategies pending further demonstration at industrial conditions, LCA, and economic assessment.Reference
- Abdulrahman, A.J., Kusenberg, M., Auersvald, M., Pernalete Piña, C., Parvizi, B., Havaei, M., Thybaut, J.W., Van Geem, K.M., 2026. Advancing circular plastics: hydrotreatment of pyrolysis oils for high‑yield ethylene production. Waste Management 211, 115287.
- Selected supporting references cited in the article: Kusenberg, M. et al., 2022. Assessing feasibility and quality of pyrolysis oils as cracker feedstocks; Zacher, A.H. et al., 2014. Review of bio‑oil hydrotreating; Pyl, S.P. et al., 2011/2012. GC×GC analysis and pyrolysis-cracking studies; Van Geem, K.M. et al., 2005. Steam cracking severity indices.
Content was automatically generated from an orignal PDF document using AI and may contain inaccuracies.