CO2 to chemicals: evaluating the potential of Fischer-Tropsch naphthas as a circular source of light olefins

Scientific articles | 2026 | REFINE LabInstrumentation
GC, GCxGC, ICP-OES
Industries
Energy & Chemicals
Manufacturer
Agilent Technologies

CO2 to chemicals: evaluating the potential of Fischer–Tropsch naphthas as a circular source of light olefins



Importance of the topic

The conversion of captured CO2 into petrochemical feedstocks is essential to decarbonize hard-to-abate industrial carbon flows. Steam cracking remains the dominant route to produce light olefins (ethylene, propylene), but replacing fossil-derived naphthas with circular carbon feedstocks is required to lower embedded carbon. Fischer–Tropsch (FT) synthesis fed by CO2 via RWGS can produce hydrocarbon streams compatible with existing steam crackers, potentially enabling scalable CO2 utilization while leveraging existing infrastructure. Assessing FT-derived naphthas’ chemical quality, cracking behavior, coke propensity, and cracker-level CO2 intensity is therefore of high practical relevance for industrial implementation.

Objectives and overview of the study

This experimental study systematically evaluates three CO2-derived FT feedstocks (crude FT oil, hydrotreated FT oil, and hydrotreated FT naphtha) produced via an integrated RWGS + FT route. Key aims were to: (i) comprehensively characterize chemical composition using GC×GC and other detectors; (ii) benchmark steam-cracking performance in a continuous bench-scale steam cracker against a reference fossil naphtha under industrially relevant conditions (COTs 820–880 °C); (iii) quantify product yields, coke formation, and oxygenate fate; and (iv) estimate the impact on cracker-level CO2 intensity for ethylene production.

Methodology and used instrumentation

- Feedstock production and upgrading:
  • CO2 converted to syngas via RWGS; syngas fed to FT reactor to produce crude FT oil.
  • Hydrotreatment performed in a two-stage bench-scale high-throughput reactor using a 3% Pt/γ‑Al2O3 catalyst: low-temperature stage (160 °C, 50 bar) to hydrogenate olefins; high-temperature stage (340 °C, 50 bar) for oxygenate removal.
  • Fractionation by distillation (Pilodist PD104HT) with a 200 °C cut to obtain FT naphtha fraction.

- Analytical characterization:
  • Comprehensive two-dimensional gas chromatography (GC×GC) with FID for hydrocarbon class and boiling-range reconstruction.
  • Sulfur and nitrogen chemiluminescence detectors (SCD, NCD) for heteroatom analysis.
  • Atomic emission detector (AED) for oxygen and chlorine-containing compounds.
  • Inductively coupled plasma optical emission spectroscopy (ICP‑OES) for metal contaminants.
  • On-line Light Oxygenates Analyzer (LOA) and refinery gas analyzer (RGA) for reactor effluent.

- Steam-cracking testing:
  • Bench-scale steam cracker (BSSC) operated at 150 g·h−1 liquid feed, steam-to-hydrocarbon mass ratio 0.5, coil inlet 550 °C, coil outlet temperatures (COT) 820, 850, 880 °C, coil outlet pressure 1.7 bar.
  • On-line product quantification via RGA, GC×GC-FID and LOA; overall mass-balance closure ±5%.

Key feedstock characteristics (analytical highlights)

- Crude FT oil: highly paraffinic and linear (≈76 wt% n‑paraffins), carbon-number range C5–C23. Unexpectedly high oxygenates (~11.7 wt%, primarily primary alcohols) and significant α‑olefins (~11.3 wt%). Negligible aromatics, naphthenes, sulfur, nitrogen, halogens; total metals low (7–14 ppm).

- Hydrotreated FT oil and HDT FT naphtha: hydrotreatment removed olefins and oxygenates to below detection limits; resulting streams are >98 wt% paraffinic, narrow boiling-range (HDT FT naphtha: IBP–FBP ~14–203 °C).

Main results and discussion

- Steam-cracking product distribution and selectivity:
  • FT-derived feeds produced substantially higher ethylene yields than fossil naphtha. At 850 °C COT: crude FT oil 37.3 wt% ethylene, HDT FT oil 40.3 wt%, HDT FT naphtha 40.8 wt% vs fossil naphtha 26.2 wt%.
  • Relative increases vs fossil: crude FT oil ~38% higher ethylene at 880 °C (paper summary numbers), and hydrotreatment further improved ethylene advantage to ~48% in some comparisons.
  • Lower propylene/ethylene (P/E) ratios for FT feeds (~0.40–0.42) versus fossil naphtha (~0.57), reflecting the predominance of linear n‑paraffins that favor β‑scission and ethylene formation.
  • FT feeds yielded less pyrolysis gasoline (PyGas, C5–C9) and substantially reduced BTX aromatics (e.g., BTX at 850 °C: fossil ≈11.9 wt% vs FT oil ≈8.3 wt%).
  • Pyrolysis fuel oil (PFO, C10+) formation was reduced for hydrotreated FT naphtha and at higher COTs; crude FT oil initially gave higher PFO at low severity due to heavy C10+ fraction but cracked more into light olefins at higher severity.

- Oxygenates and CO formation:
  • Crude FT oil oxygenates (≈11.7 wt%) produced elevated CO in the effluent (oxygen largely converted to CO at cracking temperatures >800 °C); no light oxygenates (e.g., methanol, formaldehyde) were detected in on-line LOA, indicating deep cracking of oxygenated fragments to CO/water.
  • Hydrotreatment effectively eliminated oxygenates, reducing CO formation in effluent to near background levels.

- Coke formation and fouling propensity:
  • Radiant-coil coke in a 6-hour run at 850 °C: HDT FT naphtha ≈0.08 g (lowest), FT oil and HDT FT oil ≈0.12 g.
  • These bench-scale coil coke figures suggest no major coil-coking issues for FT feeds; however, fouling and coke formation in convection and transfer-line sections were not assessed here and require dedicated fouling testing (FAST) for industrial extrapolation.

- Feedstock blending and upgrading implications:
  • Crude FT oil’s olefins (11.3 wt%) and oxygenates exceed industrial steam cracker thresholds (typical limits: olefins ~2 wt%, oxygen ~100 ppm); blending with fossil naphtha reduces olefin concentration (5 wt% FT oil blending brings olefins below 2 wt%), but oxygenates still require hydrotreatment to meet ppm-level limits.
  • Estimated net hydrogen demand for complete hydrotreatment ≈0.34 kg H2 per 100 kg FT oil (consumption relative to hydrogen supplied is low because most H2 is recycled in industrial practice); RWGS hydrogen demand remains the dominant hydrogen penalty in the CO2-to‑hydrocarbons route.

- Carbon footprint at cracker level:
  • The paraffinic FT-derived feeds increase ethylene yield per unit feed, lowering furnace fuel demand per ton of ethylene and thereby reducing cracker-level CO2 intensity.
  • Reported reductions: crude FT oil ≈22% CO2 intensity reduction vs fossil naphtha; hydrotreatment variants and optimized fractions led to up to ≈27% cracker-level CO2 intensity reduction when compared with fossil naphtha (cracker-level only; excludes upstream hydrogen/production impacts).
  • FT-derived feedstocks can also act as hydrogen-rich balancing components when co-processing hydrogen-poor circular streams (e.g., plastic pyrolysis oils), enabling blends that keep CO2 footprints near fossil baselines while allowing higher circular feedstock shares.

Benefits and practical applications

- Technical benefits:
  • FT-derived streams are very low in sulfur, nitrogen, halogens and heavy metals, reducing corrosion and downstream catalyst poisoning risks.
  • High linear-paraffin content drives greater ethylene selectivity and reduced formation of heavier aromatics/PAHs, improving carbon efficiency in steam cracking.
  • Hydrotreatment can produce a stable, narrow-boiling FT naphtha suitable for direct substitution or blending in existing steam cracker pools.

- Practical use cases:
  • Direct substitution or partial blending into naphtha crackers after appropriate upgrading (hydrotreatment and fractionation).
  • Strategic blending agent to enable co-processing of lower-quality circular feeds (e.g., plastic pyrolysis oils) without strongly degrading furnace performance or CO2 metrics.
  • Potential drop-in feed for steam crackers when produced at sufficient scale and integrated with low‑carbon hydrogen supply.

Limitations, challenges and trade-offs

- Key challenges include the presence of oxygenates in crude FT oil that necessitate hydrotreatment (hydrogen and energy cost), RWGS hydrogen demand as a major upstream energy penalty, and the need for integrated hydrogen management to preserve overall environmental benefit.

- Fouling and coke in the convection and downstream sections may still arise from residual unsaturates or contaminants and require industrial-scale validation (FAST) and appropriate blending/upgrading.

Future trends and opportunities for utilization

  • Integration and optimization of the RWGS–FT tandem (minimizing residual CO2 and improving catalyst reduction state) to reduce oxygenate formation and improve FT product slate.
  • Advanced hydrotreatment schemes and hydrogen recovery/recycle strategies to lower the net hydrogen penalty and life-cycle emissions.
  • Pilot- and demonstration-scale co-processing trials to evaluate long-term fouling, catalyst life and industrial operability, including FAST and full furnace/convection assessments.
  • Comprehensive techno‑economic analyses and full life‑cycle assessments that include upstream hydrogen production, CO2 capture, and plant integration to quantify real net CO2 savings and costs.
  • Exploration of FT catalyst and process conditions that minimize alcohol formation when using CO2‑derived syngas (e.g., cobalt reducibility control, syngas composition adjustment, or catalyst development for FT-to-olefins).

Conclusions

The study demonstrates that CO2-derived FT feedstocks are promising circular alternatives for steam cracking and light-olefin production when appropriately upgraded. FT-derived streams are clean (very low heteroatom and metal content) and highly paraffinic, delivering substantially higher ethylene yields and lower heavier by-product formation than a fossil naphtha benchmark. Hydrotreatment is necessary to remove oxygenates and stabilize crude FT oil for cracker compatibility; this upgrading incurs hydrogen and energy costs that partially offset carbon advantages but can be optimized through integration. FT-derived naphtha can also act as a balancing feed to enable higher shares of challenging circular feeds in cracker pools. Further work should focus on RWGS–FT integration, hydrogen management, industrial fouling/coking testing, and complete life-cycle techno‑economic studies to validate large-scale implementation.

Used instrumentation (concise list)

  • FT production: RWGS + FT reactors (VTT configuration with CPOX/RWGS coupling described in SI).
  • Hydrotreatment: bench-scale high-throughput reactor with 3% Pt/γ‑Al2O3 catalyst; two-stage hydrotreating at 160 °C and 340 °C (50 bar).
  • Fractionation: Pilodist PD104HT distillation unit (200 °C cut for naphtha).
  • Analytical: GC×GC–FID, GC×GC–SCD, GC×GC–NCD, GC×GC–AED, ICP‑OES, LOA, RGA.
  • Steam-cracking testing: Bench-Scale Steam Cracker (BSSC) at Ghent University with on-line sampling and GC×GC-based product analysis.

Reference

  1. IPCC, Climate Change 2023: Synthesis Report. Contribution of Working Groups I, II and III to the Sixth Assessment Report of the Intergovernmental Panel on Climate Change, 2023.
  2. IEA, Energy Efficiency 2025, International Energy Agency, Paris, 2025.
  3. IEA, Policy Toolbox for Industrial Decarbonisation, IEA, Paris, 2025.
  4. IRENA, Decarbonising hard-to-abate sectors with renewables: Perspectives for the G7, 2024.
  5. M. Mynko et al., Electrification of steam cracking as a pathway to reduce the impact of the petrochemical industry on climate change, J. Clean. Prod., 2023.
  6. K.M. Van Geem, V.V. Galvita, G.B. Marin, Making chemicals with electricity, Science, 2019.
  7. R. Cuéllar‑Franca et al., Utilising carbon dioxide for transport fuels: economic/environmental analysis of FT process designs, Appl. Energy, 2019.
  8. G. Tweddle et al., Alternative Naphtha – Replacing Fossil-Based Feedstocks in Refineries and Naphtha Crackers, nova-Institute, 2024.
  9. IEA, Global energy review, 2021.
  10. Y. Cao et al., Synthesis gas production via coal gasification: effects of coal ranks and methane addition, Energy & Fuels, 2008.
  11. M.E. Dry, High quality diesel via the Fischer–Tropsch process – a review, J. Chem. Technol. Biotechnol., 2002.
  12. P. Jaramillo et al., Comparative Analysis of the Production Costs and Life-Cycle GHG Emissions of FT Liquid Fuels, Environ. Sci. Technol., 2008.
  13. I. Dimitriou et al., Carbon dioxide utilisation for transport fuels: process and economic analysis, Energy & Environ. Sci., 2015.
  14. B.C.A. de Jong et al., Sustainable Fuels from CO2‑Rich Synthesis Gas via Fischer–Tropsch Technology, ACS Catal., 2025.
  15. M. Ostadi et al., Hydrogen-Enhanced Biomass/Municipal Solid Waste Gasification, Sustainability, 2025.
  16. D. Unruh et al., Fischer–Tropsch Synfuels from Biomass: Maximizing Carbon Efficiency, Energy & Fuels, 2010.
  17. Y. Gao et al., Recent advances in iron-based catalysts for Fischer–Tropsch to olefins, Catal. Commun., 2023.
  18. A. Yahyazadeh et al., Fischer–Tropsch synthesis for light olefins from syngas: catalyst review, Reactions, 2021.
  19. A. Karaba et al., Fischer-Tropsch Wax from Renewable Resources as an Excellent Feedstock for Steam-Cracking, Chem. Eng. & Technol., 2021.
  20. L.P. Dancuar et al., Performance of the Sasol SPD naphtha as steam cracking feedstock, 2003.
  21. F. Wang et al., Steam cracking of Fischer–Tropsch naphtha for light olefins, Chem. Eng. Process., 2010.
  22. P. Neuner et al., Chemical Conversion of Fischer–Tropsch Waxes and Plastic Waste Pyrolysis Condensate, Reactions, 2022.
  23. K.M. Van Geem et al., Dimensional analysis for scaling up and down steam cracking coils, Chem. Eng. J., 2007.
  24. S.P. Pyl et al., Rapeseed oil methyl ester pyrolysis: GC×GC analysis, J. Chromatogr. A, 2011.
  25. M.R. Harper et al., Reaction mechanism for n-butanol pyrolysis and combustion, Combust. Flame, 2011.
  26. M. Kusenberg et al., Assessing feasibility of steam cracking of untreated plastic waste pyrolysis oils, Waste Manag., 2022.
  27. M. Kusenberg et al., Experimental investigation of plastic waste pyrolysis oil quality, Fuel Process. Technol., 2022.
  28. M. Kusenberg et al., Contaminant removal from plastic waste pyrolysis oil via depth filtration, Chem. Eng. J., 2023.
  29. Ad Klerk, Fischer–Tropsch fuels refinery design, Energy & Environmental Science, 2011.
  30. T. Ishida et al., Synthesis of higher alcohols by Fischer–Tropsch over alkali-modified cobalt catalysts, Appl. Catal. A, 2013.
  31. H. Du et al., Enhanced silica-supported cobalt catalyst for alcohols from syngas, Int. J. Hydrog. Energy, 2022.
  32. Y. Pei et al., One-step production of C1–C18 alcohols via FT on activated carbon-supported cobalt, Chin. J. Catal., 2015.
  33. Y.-P. Pei et al., High Alcohols Synthesis via FT at Cobalt Metal/Carbide Interface, ACS Catal., 2015.
  34. A. Kharrazi et al., Enhancement of higher alcohols selectivity in FT using biochar supports, J. Energy Inst., 2024.
  35. T.A. Zepeda, Selectivity modulation in FT through reducibility control of cobalt species, Catal. Today, 2025.
  36. H.E. du Plessis et al., in situ reduction study of cobalt model FT catalysts, Phys. Chem. Chem. Phys., 2013.
  37. M.K. Gnanamani et al., Effect of CO2-containing syngas over promoted catalysts, Catal. Commun., 2011.
  38. Y. Yao et al., Effect of CO2 on cobalt-based catalyst for low-temperature FT, Chem. Eng. J., 2012.
  39. S.-M. Kim et al., Effect of CO2 in feed on deactivation of Co/γ‑Al2O3 FT catalyst, Catal. Commun., 2008.
  40. G. Bekmukhamedov et al., Direct combination of RWGS and FTS for fuels, Chem. Eng. J., 2026.
  41. P. Hirunsit et al., From CO2 to Sustainable Aviation Fuel: Technology Landscape, ACS Sustain. Chem. Eng., 2024.
  42. N. Ibrić et al., Direct conversion of CO2 and H2 to liquid fuels via FT: process concept, J. CO2 Util., 2026.
  43. M. Kusenberg et al., Maximizing olefin production via steam cracking of distilled pyrolysis oils, Sci. Total Environ., 2022.
  44. S.P. Pyl et al., Comprehensive study of methyl decanoate pyrolysis, Energy, 2012.
  45. M. Kusenberg et al., Opportunities and challenges for plastic waste pyrolysis oils as steam cracker feedstocks, Waste Manag., 2022.
  46. C. Delhomme-Neudecker et al., Plastic pyrolysis oils as feedstock for steam crackers: Part 1, Hydrocarb. Process., 2024.
  47. N.D. Ristic et al., Quantitative compositional analysis of Estonian shale oil using GC×GC, Fuel Process. Technol., 2017.
  48. Y. Li et al., Formation of gum and deposits in an oxygenated naphtha stream, 2007.
  49. S.P. Pyl et al., Wood-derived olefins by steam cracking of hydrodeoxygenated tall oils, Bioresour. Technol., 2012.
  50. Z. Gholami et al., Review on production of light olefins using steam cracking, Energies, 2021.
  51. O. Herbinet et al., Thermal decomposition of n-dodecane: experiments and modeling, J. Anal. Appl. Pyrolysis, 2007.
  52. K.M. Van Geem et al., Molecular reconstruction of naphtha steam cracking feedstocks, Comput. Chem. Eng., 2007.
  53. K.M. Van Geem et al., Challenges of modeling steam cracking of heavy feedstocks, Oil & Gas Sci. Technol., 2008.
  54. T. Dijkmans et al., Production of bio-ethene and propene: alternatives for bulk chemicals, Green Chem., 2013.
  55. R. De Bruycker et al., Assessing crude tall oil for green-base chemicals: experimental and modeling study, Ind. Eng. Chem. Res., 2014.
  56. R. De Bruycker et al., Steam cracking of bio-derived normal and branched alkanes: influence of branching, J. Anal. Appl. Pyrolysis, 2016.
  57. N.M. Vandewiele et al., Thermal decomposition of Jet Propellant-10, Energy & Fuels, 2014.
  58. K.M.V. Geem et al., Coke formation in the transfer line exchanger during steam cracking, Ind. Eng. Chem. Res., 2009.
  59. L. dos S. Vargette et al., Determining fouling tendency in the Fouling Assessment Setup, Heat Mass Transf., 2024.
  60. H.M. Shirazi et al., Impact of temperature and feedstock composition on coke formation in steam cracking reactors, Heat Mass Transf., 2025.
  61. O. Mynko et al., Reducing CO2 emissions of existing ethylene plants: evaluation of revamp strategies, J. Clean. Prod., 2022.

Content was automatically generated from an orignal PDF document using AI and may contain inaccuracies.

Downloadable PDF for viewing
 

Similar PDF

Advancing circular plastics: hydrotreatment of pyrolysis oils for high-yield ethylene production
Production of secondary raw materials from the hydrotreating of plastic waste pyrolysis oils
Toward accurate olefin quantification in plastic waste oils: Analytical strategies and future directions
Upgrading of hydrothermal liquefaction biocrudes from mono- and co-liquefaction of cow manure and wheat straw through hydrotreating and distillation