Bio-based refinery intermediate production via hydrodeoxygenation of fast pyrolysis bio-oil

Scientific articles | 2021 | REFINE LabInstrumentation
GC/MSD, GC
Industries
Energy & Chemicals
Manufacturer
Agilent Technologies

Significance of the topic


Fast pyrolysis bio-oil from lignocellulosic biomass is an abundant, renewable liquid feedstock with potential as a refinery co-feed for hybrid transportation fuels. However, its high oxygen and water content, strong acidity and thermal instability prevent direct use. Mild hydrotreatment (HDT) / hydrodeoxygenation (HDO) can partially stabilize and deoxygenate bio-oil to produce a refinery-compatible intermediate that enables co-processing in existing refineries with lower capital intensity than full standalone biofuel plants.

Objectives and study overview


This study evaluated upgrading of an organic-phase fast pyrolysis bio-oil (50:50 barley:wheat straw feedstock) by continuous mild hydrotreatment in a TRL3 pilot plant. The aims were to determine process performance, catalyst life and product quality under different operating windows and to assess whether a mid-severity HDT step can yield a reliable refinery intermediate suitable for co-processing.

Key experimental variables tested:
  • Reaction temperature: 573, 603 and 633 K
  • H2 partial pressure: 4 and 7 MPa
  • H2/bio-oil volumetric ratio: 506 and 843 NL H2 per L bio-oil

Materials, methodology and used instrumentation


Feedstock and catalyst:
  • Organic fraction of ablative fast pyrolysis bio-oil (barley:wheat straw 1:1); initial properties: density 1.024 g/mL, hydrogen 8.32 wt%, carbon 53.92 wt%, oxygen ~37.6 wt%, dissolved water ~21.9 wt%, TAN 219 mgKOH/g, kin. viscosity 156 cSt.
  • Commercial Ranido NiMo/Al2O3 hydrotreating catalyst (particle size 0.8–1.2 mm), diluted with inert material (inert/catalyst 5.6 v/v) and presulfided prior to use.

Pilot plant and operation:
  • Continuous-flow hydroprocessing pilot plant (CERTH CPERI TRL3).
  • Liquid hourly space velocity (LHSV) fixed at 1 h−1 and feed flow rate 20 mL/h for all runs.
  • Each condition was run to steady state (typically 2–3 days on stream); product analysis focused on the third day sample.

Analytical methods and instruments (selected):
  • Gas analysis: on-line Agilent 7890 GC (FID + two TCDs) for permanent gases and hydrocarbons.
  • GC–MS for volatile compound quantification (direct quantification of >100 compounds; secondary quantification by surrogate response factors).
  • Elemental analysis (C, H, S) by ASTM methods and LECO instrumentation for hydrogen measurement.
  • Density by ASTM D4052; simulated distillation by ASTM D7169; sulphur by ASTM D5453; dissolved water by ASTM D1744 (Karl Fischer); TAN by ASTM D664; kinematic viscosity ISO 3104; MCR by ASTM D4530; Faix and potentiometric titration methods for carbonyls and carboxylic acids; Folin–Ciocalteu for total phenolics.

Main results and discussion


Catalyst life and reactor operability:
  • Catalyst deactivation and reactor plugging by coke were major limitations for continuous operation. Coke formed from reactive unsaturated oxygenates (phenolics, furans, etc.) and polymerization products, causing rapid pressure drop (DP) in the packed bed.
  • Best catalyst life observed: 5 days on stream under 603 K, 7 MPa and 843 NL/L H2/bio-oil.
  • Higher hydrogen partial pressure and higher H2/bio-oil ratio extended catalyst life and reduced the rate of DP build-up; lower pressure or lower hydrogen ratio accelerated coking and premature termination of runs.

Product yields, phase separation and bulk properties:
  • Hydrotreatment produced a two-phase liquid: a low-polarity organic top layer (target product) and an aqueous bottom layer (water formed by dehydration/decarboxylation). Aqueous-phase yields for most conditions were ~37–40 vol%.
  • Significant improvements in organic-phase properties were achieved: kinematic viscosity fell from 156 to as low as 4.9 cSt, density decreased from 1.024 to ~0.916 g/mL, carboxylic acid number (CAN) dropped from 78 to ~0.2 mgKOH/g, and bulk oxygen content was reduced from ~37 wt% to ~4 wt% (over 90% oxygen removal in many cases). Dissolved water in the organic phase was essentially eliminated due to polarity reduction.
  • Increasing reaction temperature favored cracking and hydrogenation: gasoline+diesel fraction (by simulated distillation up to 633 K cut) increased from ~56 wt% to ~72 wt% comparing the lowest and highest temperature runs, and carbon residue (MCR) decreased with more severe cracking.

Molecular composition (GC–MS and spectrometric results):
  • Most volatile oxygenates (aldehydes, ketones, etc.) were hydrogenated and removed from the organic phase in all conditions; phenolic compounds remained the dominant detectable oxygenates in the upgraded organic product.
  • Higher temperature and hydrogen availability increased hydrocarbon yields and decreased olefin fractions (olefins result from cracking/isomerization and can be hydrogenated to paraffins when sufficient H2 is available).
  • At the highest temperature (633 K) and 7 MPa, notable cracking of lignin-derived heavy fragments increased volatile phenol production transiently, reflecting competitive decomposition vs. hydrogenation.

Gaseous products and hydrogen consumption:
  • Gas streams contained H2 (consumed), light hydrocarbons (CH4, C2–C3 hydrocarbons), CO and CO2. Carbon lost as gases (notably CO2 and CH4) reduced liquid carbon yield; formation of CO and CO2 indicates decarbonylation/decarboxylation pathways competing with HDO (water formation).
  • Lower H2/bio-oil ratio promoted CO2 formation; lower pressure favored CO formation; lower temperature increased CH4 formation.
  • Hydrogen consumption increased with higher reaction temperature and with higher pressure/H2 ratio (because more extensive hydrogenation and HDO occurred). Hydrogen usage must be optimized due to cost and supply constraints.

Process limitations identified:
  • Severe catalyst coking and reactor plugging remain the primary operational barriers for continuous mild-HDT of raw pyrolysis bio-oil.
  • Feed impurities (minerals) and highly reactive unsaturated oxygenated species promote catalyst deactivation and coke formation.

Practical benefits and potential applications


The study demonstrates that a mild hydrotreatment pre-step can convert raw fast pyrolysis bio-oil into an organic-phase intermediate with substantially improved physical and chemical properties suitable for refinery co-processing. Practical outcomes include:
  • A pathway to produce a mid-distillate-rich intermediate (diesel/gasoline range) with lower oxygen and acid content for co-feeding into existing hydrotreating/hydrocracking refinery units.
  • Reduced corrosivity and improved miscibility prospects with petroleum fractions compared to raw bio-oil.
  • Potential to lower capital cost vs. dedicated full-scale biofuel plants by leveraging existing refinery conversion capacity (co-processing).

Used instrumentation


  • Hydroprocessing pilot plant (CERTH CPERI TRL3 continuous packed-bed reactor).
  • Ranido NiMo/Al2O3 hydrotreating catalyst (presulfided).
  • Agilent 7890 GC with FID and two TCDs for on-line gas analysis.
  • GC–MS for volatile liquid composition analysis.
  • Elemental analysis instruments (LECO or equivalent) for C/H/S, plus standard laboratory equipment for ASTM/ISO methods: density (D4052), simulated distillation (D7169), sulphur (D5453), water (D1744), TAN (D664), viscosity (ISO3104), MCR (D4530).

Future trends and opportunities for application


Key directions to advance continuous bio-oil upgrading include:
  • Catalyst development: design of coke-resistant catalysts or bifunctional materials that selectively hydrogenate/reactive species while limiting polymerization; tailored supports and promoters to mitigate poisoning from inorganic contaminants.
  • Feed pretreatment / staged upgrading: mild stabilization steps carried out at lower temperature to hydrogenate carbonyls before higher-severity cracking to reduce coke precursors; fractionation of bio-oil to remove or process problematic streams separately.
  • Process integration: on-site hydrogen generation (e.g., reforming of by-product gases), recycle strategies, and optimization of H2 utilization to reduce operating cost.
  • Scale-up and refinery integration studies: miscibility tests with refinery streams, co-processing trials, techno-economic analysis and life-cycle assessment to quantify benefits and commercial feasibility.
  • Alternative hydrogen sources and lower-severity pathways (e.g., hydrogen-donor solvents) to reduce dependence on high-pressure H2.

Conclusions


This work shows that mild hydrotreatment of fast pyrolysis bio-oil can produce a substantially upgraded organic intermediate: viscosity, acidity and oxygen content were markedly reduced and hydrocarbon fractions in the diesel/gasoline boiling range were increased. However, continuous operation is challenged by rapid catalyst coking and reactor plugging driven by reactive unsaturated oxygenates and feed impurities. Optimal conditions in this study (603 K, 7 MPa, 843 NL/L H2/bio-oil) extended catalyst life to 5 days and yielded the best overall product quality. Mild-HDT is therefore a promising route to generate refinery-compatible bio-based intermediates, but further R&D is required on catalyst resilience, feed stabilization and hydrogen-management to enable sustainable continuous operation at scale.

Reference


  1. EIBI, European Industrial Bioenergy Initiative. http://www.etipbioenergy.eu/?option=com_content&view=article&id=191 (accessed 07 Jan 2019).
  2. SETIS, Strategic Energy Technology Information System. https://setis.ec.europa.eu (Accessed 7 January 2019).
  3. A. Dimitriadis, A. Dimaratos, S. Doulgeris, S. Bezergianni, Z. Samaras, Emissions Optimization Potential of a Diesel Engine Running on HVO: a Combined Experimental and Simulation Investigation, SAE Technical Paper, 2019.
  4. A. Dimitriadis, T. Seljak, R. Vihar, U.Z. Baškovic, A. Dimaratos, S. Bezergianni, Z. Samaras, T. Katrašnik, Improving PM-NOx trade-off with paraffinic fuels: a study towards diesel engine optimization with HVO, Fuel 265 (2020).
  5. M. Krar, S. Kovacs, D. Kallo, J. Hancsok, Fuel purpose hydrotreating of sunflower oil on CoMo/Al2O3 catalyst, Bioresour. Technol. 101 (2010) 9287–9293.
  6. S. Bezergianni, A. Dimitriadis, Comparison between different types of renewable diesel, Renew. Sustain. Energy Rev. 21 (2013) 110–116.
  7. S. Bezergianni, A. Dimitriadis, O. Kikhtyanin, D. Kubicka, Refinery coprocessing of renewable feeds, Prog. Energy Combust. Sci. 68 (2018) 29–64.
  8. L.P. Chrysikou, V. Dagonikou, A. Dimitriadis, S. Bezergianni, Waste cooking oils exploitation targeting EU 2020 diesel production: environmental and economic benefits, J. Clean. Prod. 219 (2019) 566–575.
  9. R.P. Anex, A. Aden, F.K. Kazi, J. Fortman, R.M. Swanson, M.M. Wright, Technoeconomic comparison of biomass-to-transportation fuels via pyrolysis, gasification, and biochemical pathways, Fuel 89 (2010) S29–S35.
  10. P.J. Dauenhauer, J.L. Colby, C.M. Balonek, W.J. Suszynski, L.D. Schmidt, Reactive boiling of cellulose for integrated catalysis through an intermediate liquid, Green Chem. 11 (2009) 1555–1561.
  11. S. Conrad, A. Apfelbacher, T. Schulzke, Fractionated condensation of pyrolysis vapours from ablative flash pyrolysis, 22nd European Biomass Conference & Exhibition, 2014.
  12. T.N. Trinh, P.A. Jensen, K.D. Johansen, N.O. Knudsen, H.R. Sørensen, S. Hvilsted, Comparison of lignin, macroalgae, wood, and straw fast pyrolysis, Energy Fuels 27 (2013) 1399–1409.
  13. P.M. Mortensen, J.-D. Grunwaldt, P.A. Jensen, K.G. Knudsen, A.D. Jensen, A review of catalytic upgrading of bio-oil to engine fuels, Appl. Catal. A 407 (2011) 1–19.
  14. A. Oasmaa, R. Alén, Catalytic hydrotreatment of some technical lignins, Bioresour. Technol. 45 (1993) 189–194.
  15. D.C. Elliott, Historical developments in hydroprocessing bio-oils, Energy Fuel. 21 (2007) 1792–1815.
  16. J. Wildschut, F.H. Mahfud, R.H. Venderbosch, H.J. Heeres, Hydrotreatment of fast pyrolysis oil using heterogeneous noble-metal catalysts, Ind. Eng. Chem. Res. 48 (2009) 10324–10334.
  17. Z. Yang, A. Kumar, R.L. Huhnke, Review of recent developments to improve storage and transportation stability of bio-oil, Renew. Sustain. Energy Rev. 50 (2015) 859–870.
  18. N. Li, G.W. Huber, Aqueous-phase hydrodeoxygenation of sorbitol with Pt/SiO2–Al2O3, J. Catal. 270 (2010) 48–59.
  19. N. Li, G.A. Tompsett, G.W. Huber, Renewable high-octane gasoline by aqueous-phase hydrodeoxygenation of C5 and C6 carbohydrates over Pt/zirconium phosphate catalysts, ChemSusChem 3 (2016) 1154–1157.
  20. T. Dickerson, J. Soria, Catalytic fast pyrolysis: a review, Energies 6 (2013) 514–538.
  21. S. Kadarwati, X. Hu, R. Gunawan, R. Westerhof, M. Gholizadeh, M.D.M. Hasan, C.-Z. Li, Coke formation during the hydrotreatment of bio-oil using NiMo and CoMo catalysts, Fuel Process. Technol. 155 (2017) 261–268.
  22. X. Hu, Y. Wang, D. Mourant, R. Gunawan, C. Lievens, W. Chaiwat, M. Gholizadeh, L. Wu, X. Li, C.-Z. Li, Polymerization on heating up of bio-oil: a model compound study, AIChE J. 59 (2013) 888–900.
  23. M. Gholizadeh, R. Gunawan, X. Hu, S. Kadarwati, R. Westerhof, W. Chaiwat, M. Hasan, C.-Z. Li, Importance of hydrogen and bio-oil inlet temperature during the hydrotreatment of bio-oil, Fuel Process. Technol. 150 (2016) 132–140.
  24. Y. Wang, D. Mourant, X. Hu, S. Zhang, C. Lievens, C.-Z. Li, Formation of coke during the pyrolysis of bio-oil, Fuel 108 (2013) 439–444.
  25. R.H. Venderbosch, A.R. Ardiyanti, J. Wildschut, A. Oasmaa, H.J. Heeres, Stabilization of biomass-derived pyrolysis oils, J. Chem. Technol. Biotechnol. 85 (2010) 674–686.
  26. D.C. Elliott, T.R. Hart, G.G. Neuenschwander, L.J. Rotness, A.H. Zacher, Catalytic hydroprocessing of biomass fast pyrolysis bio-oil to produce hydrocarbon products, Environ. Prog. Sustain. Energy 28 (2009) 441–449.
  27. A. Sanna, T.P. Vispute, G.W. Huber, Hydrodeoxygenation of the aqueous fraction of bio-oil with Ru/C and Pt/C catalysts, Appl. Catal. B Environ. 165 (2015) 446–456.
  28. Y. Han, M. Gholizadeh, C.-C. Tran, S. Kaliaguine, C.-Z. Li, M. Olarte, M. Garcia-Perez, Hydrotreatment of Pyrolysis Bio-Oil: A Review, Fuel Process. Technol. 195 (2019) 106140.
  29. E. Furimsky, Chemistry of catalytic hydrodeoxygenation, Catal. Rev. Sci. Eng. 25 (1983) 421–458.
  30. E. Furimsky, Catalytic hydrodeoxygenation, Appl. Catal. A 199 (2000) 147–190.
  31. X. Li, R. Gunawan, Y. Wang, W. Chaiwat, X. Hu, M. Gholizadeh, D. Mourant, J. Bromly, C.-Z. Li, Upgrading of bio-oil into advanced biofuels and chemicals. Part III. Changes in aromatic structure and coke forming propensity during the catalytic hydrotreatment of a fast pyrolysis bio-oil with Pd/C catalyst, Fuel 116 (2014) 642–649.
  32. M. Gholizadeh, R. Gunawan, X. Hu, M.M. Hasan, S. Kersten, R. Westerhof, W. Chaitwat, C.-Z. Li, Different reaction behaviours of the light and heavy components of bio-oil during the hydrotreatment in a continuous packed-bed reactor, Fuel Process. Technol. 146 (2016) 76–84.
  33. A. Zacher, M. Olarte, D. Santosa, D.C. Elliott, B. Jones, A review and perspective of recent bio-oil hydrotreating research, Green Chem. 16 (2014) 491–515.
  34. T. Schulzke, S. Conrad, J. Westermeyer, Fractionation of flash pyrolysis condensates by staged condensation, Biomass Bioenergy 95 (2016) 287–295.
  35. J. Horacek, D. Kubicka, Bio-oil hydrotreating over conventional CoMo & NiMo catalysts: the role of reaction conditions and additives, Fuel 198 (2017) 49–57.
  36. S. Bezergianni, A. Dimitriadis, Temperature effect on co-hydroprocessing of heavy gas oil-waste cooking oil mixtures for hybrid diesel production, Fuel 103 (2013) 579–584.
  37. A. Dimitriadis, S. Bezergianni, Co-hydroprocessing gas-oil with residual lipids: effect of residence time and H2/Oil ratio, J. Clean. Prod. 131 (2016) 321–326.
  38. ASTM D4052, D7169, D5453, D5291, D1744, D664, D4530 and ISO 3104 standard methods as cited in the study for density, simulated distillation, sulfur, CHN, water, TAN, MCR and viscosity measurements.
  39. E. Christensen, J. Ferrell, M.V. Olarte, A.B. Padmaperuma, T. Lemmon, Acid Number Determination of Pyrolysis Bio-oils Using Potentiometric titration: Laboratory Analytical Procedure (LAP), NREL, 2016.
  40. M.R. Rover, R.C. Brown, Quantification of total phenols in bio-oil using the Folin–Ciocalteu method, J. Anal. Appl. Pyrolysis 104 (2013) 366–371.
  41. M. Auersvald, B. Shumeiko, M. Stas, D. Kubicka, J. Chudoba, P. Simacek, Quantitative study of straw bio-oil hydrodeoxygenation over a sulfided NiMo catalyst, ACS Sustain. Chem. Eng. 7 (2019) 7080–7093.
  42. Q. Bu, H. Lei, A.Z. Zacher, L. Wang, S. Ren, J. Liang, Y. Wei, Y. Liu, J. Tang, Q. Zhang, R. Ruan, A review of catalytic hydrodeoxygenation of lignin-derived phenols from biomass pyrolysis, Bioresour. Technol. 124 (2012) 470–477.
  43. T. Cordero-Lanzac, R. Palos, I. Hita, J.M. Arandes, J. Rodriguez-Mirasol, T. Cordero, J. Bilbao, P. Castano, Revealing the pathways of catalyst deactivation by coke during the hydrodeoxygenation of raw bio-oil, Appl. Catal. B 239 (2018) 513–524.
  44. C.C. Schmitt, K. Raffelt, A. Zimina, B. Krause, T. Otto, M. Rapp, J. Grunwaldt, N. Dahmen, Hydrotreatment of fast pyrolysis bio-oil fractions over nickel-based catalyst, Top. Catal. 61 (2018) 1769–1782.
  45. T. Cordero-Lanzac, R. Palos, J.M. Arandes, P. Castano, J. Rodriguez-Mirasol, T. Cordero, J. Bilbao, Stability of an acid activated carbon based bifunctional catalyst for the raw bio-oil hydrodeoxygenation, Appl. Catal. B 203 (2017) 389–399.
  46. P.M. Mortensen, D. Gardini, C.D. Damsgaard, J.-D. Grunwaldt, P.A. Jensen, J.B. Wagner, A.D. Jensen, Deactivation of Ni-MoS2 by bio-oil impurities during hydrodeoxygenation of phenol and octanol, Appl. Catal. A 523 (2016) 159–170.
  47. C.A. Mullen, A.A. Boateng, Mild hydrotreating of bio-oils with varying oxygen content produced via catalytic fast pyrolysis, Fuel 245 (2019) 360–367.
  48. M. Mohammada, T.H. Kandaramath, Z. Yaako, Y.C. Sharma, K. Sopian, Overview on the production of paraffiin-based biofuels via catalytic hydrodeoxygenation, Renew. Sustain. Energy Rev. 22 (2013) 121–132.
  49. O.I. Senol, E.M. Ryymin, T.R. Viljava, A.O.I. Krause, Reactions of methyl heptanoate hydrodeoxygenation on sulphided catalysts, J. Mol. Catal. Chem. 268 (2007) 1–8.
  50. S. Jones, C. Valkenburg, C. Walton, D. Elliott, J. Holladay, D. Stevens, C. Kinchin, S. Czernik, Production of Gasoline and Diesel from Biomass via Fast Pyrolysis, Hydrotreating and Hydrocracking: a Design Case. PNNL, Richland, WA, 2009.
  51. S. Arbogast, D. Bellman, J.D. Paynter, J. Wykowski, Advanced biofuels from pyrolysis oil…Opportunities for cost reduction, Fuel Process. Technol. 106 (2013) 518–525.

Content was automatically generated from an orignal PDF document using AI and may contain inaccuracies.

Downloadable PDF for viewing
 

Similar PDF

Efficient One-Stage Bio-Oil Upgrading over Sulfided Catalysts
Hydrotreatment of straw bio-oil from ablative fast pyrolysis to produce suitable refinery intermediates
Quantitative Study of Straw Bio-oil Hydrodeoxygenation over a Sulfided NiMo Catalyst
Advancing circular plastics: hydrotreatment of pyrolysis oils for high-yield ethylene production