GC, Pyrolysis, FTIR Spectroscopy, GC/MSD
IndustriesEnergy & Chemicals
ManufacturerThermo Fisher Scientific, Shimadzu, Agilent Technologies
Hydrotreatment of Straw Bio‑Oil from Ablative Fast Pyrolysis — Expert Summary
Significance of the topic
Upgrading lignocellulosic residues such as straw into liquid refinery‑feedstock is a key pathway to increase second‑generation biofuel supply demanded by policy frameworks (e.g., RED II). Ablative fast pyrolysis (AFP) produces bio‑oil from bulky agricultural residues without energy‑intensive grinding and can be deployed close to feedstock sources. However, crude pyrolysis oil contains high oxygen content, high acidity and water content, and is thermally/chemically unstable; therefore stabilization (partial deoxygenation) is required before co‑processing in conventional refinery units. This study defines hydrotreatment conditions to convert straw AFP bio‑oil into a practical refinery intermediate while preserving energy content and producing material miscible with middle distillates.
Objectives and study overview
- Main objective: optimize continuous hydrotreatment of straw AFP bio‑oil to obtain an organic fraction suitable for conventional refinery co‑processing rather than a fully deoxygenated product.
- Approach: continuous fixed‑bed hydrotreating over a commercial sulfided NiMo/Al2O3 catalyst; systematic variation of temperature (240–360 °C) and hydrogen pressure (2–8 MPa) at WHSV ≈ 1 h−1 and H2 flow ≈ 90 L·h−1.
- Secondary objective: establish rapid, practical analytical screening methods to assess degree of deoxygenation and product quality (SIMDIS recovery and FTIR‑PCA).
Used instrumentation
- Fixed‑bed continuous reactor (ID 23 mm) with thermo‑well and multiple thermocouples; 55 g commercial NiMo/Al2O3 catalyst (sulfided in situ).
- Hydrogen supply (99.9 vol%).
- GC‑FID/TCD systems for off‑gas analysis (permanent gases, C1–C5, and C6+ hydrocarbons/oxygenates).
- Simulated distillation (GC SIMDIS) using on‑column injector and CP‑SimDist column to evaluate fractional boiling distribution and a derived SIMDIS “recovery” metric sensitive to oxygenate vs hydrocarbon response.
- FTIR‑ATR spectrometer (4000–650 cm−1) coupled with principal component analysis (PCA) for rapid classification of product type and deoxygenation depth.
- Elemental analyzer (CHNS), Karl‑Fischer titration for water, TAN/CAN titrations, Stabinger viscometer for density/viscosity, micro‑Conradson residue, and bomb calorimetry for HHV/LHV.
Methodology
- Feed: bio‑oil from AFP of wheat/barley straw (1:1) produced at ~550 °C with vapour residence <1 s; feed doped with 0.5 wt% dimethyl disulfide (DMDS) to maintain catalyst sulfidity.
- Catalyst activation: in situ sulfiding at 345 °C, 4 MPa; stabilization on straight‑run gas oil prior to bio‑oil feed.
- Routine sampling: liquid phases (organic + aqueous) separated and characterized; gas collected in Tedlar bags for GC analysis. Time on stream (TOS) monitored; experiments run with fresh catalyst for sets of conditions.
- Rapid product assessment: SIMDIS recovery used as a proxy for hydrocarbon‑likeness; FTIR spectra analyzed by PCA to classify water content, carbonyl, aromatic/etheric features and to provide near‑real‑time control feedback.
Main results and discussion
- Liquid yields: hydrotreatment produced >90 wt% liquid yields across most conditions; the most severe condition (360 °C, 8 MPa) gave ≈88.5 wt% total liquid. Gas yields were typically 2–10 wt% and mass balances were near closed.
- Phase behavior: under mild conditions (<300 °C) organic phase yield was higher and aqueous phase <33 wt% (water in feed ≈22.6 wt%). With increasing severity (>300 °C) deoxygenation yielded more aqueous (water + extracted oxygenates) and lighter organic fractions; organic phase density and acidity decreased.
- Elemental trends: temperature increase from 240→360 °C raised H/C and decreased O/C (Van Krevelen), consistent with progressive hydrogenation and deoxygenation. Higher H2 pressure (up to 8 MPa) promoted hydrogenation/deoxygenation (e.g., H/C ~1.4→1.6 at 320–340 °C when pressure increased from 2→8 MPa).
- Energy retention: >85% of feed energy (LHV basis) could be preserved in the organic phase; the most severe condition (360 °C, 8 MPa) led to the highest SIMDIS recovery (≈96%), indicating near‑hydrocarbon composition.
- Acidity and stability: TAN and CAN decreased markedly with severity. At 360 °C and 8 MPa, TAN fell below ≈2 mg KOH·g−1 and CAN ≈3 mg KOH·g−1; water content of the organic phase dropped <1 wt% and micro‑Conradson residue (coking propensity) decreased—indicating product stability suitable for refinery processing.
- Miscibility with refinery streams: only the product from 360 °C / 8 MPa was fully miscible with straight‑run gas oil (SRGO), making it the best candidate for co‑processing.
- Gas composition and cracking: gaseous products increased markedly above ~280 °C. Methane dominated and C2–C4 gases also rose with severity; CO2/CO ratio fell from ≈3.5 at 240 °C to ≈1.4 above ~280 °C. Ratios of saturated/unsaturated light hydrocarbons indicated hydrogenation of alkenes at higher severity and increased cracking at elevated temperatures.
- Rapid analytics validated: SIMDIS recovery correlated with degree of deoxygenation and boiling distribution (gasoline/diesel/heavy fractions). FTIR spectra processed by PCA segregated water/aqueous phases from organic products and allowed ranking of deoxygenation depth and structural changes (carbonyl loss, increase of aliphatic CH bands), supporting their use for near‑real‑time monitoring and process control.
Benefits and practical applications
- The study demonstrates that AFP straw bio‑oil can be partially upgraded by conventional sulfided NiMo hydrotreatment to yield refinery‑compatible intermediates while retaining most feed energy.
- Products from optimized conditions (notably 360 °C / 8 MPa) show low acidity, low water, low coking tendency and miscibility with middle distillates — enabling co‑processing in existing refinery units and leveraging refinery overcapacity to scale up advanced biofuels production.
- The proposed rapid analytical workflows (SIMDIS recovery and FTIR‑PCA) deliver actionable, short‑time diagnostics for process control and product specification monitoring — valuable for continuous operation and catalyst life management.
Future trends and potential uses
- Catalyst optimization and durability: addressing sulfided catalyst deactivation in water/oxygenate environments (H2S management, support stabilization, alternative supports) will be critical for long‑term operation and scale‑up.
- Alternative catalysts and processes: metal phosphides, carbides, nitrides and non‑sulfided noble/transition metal systems may offer different selectivity/hydrogen consumption tradeoffs and deserve further study.
- Process integration: two‑stage hydrotreatment (mild stabilization followed by deeper HDO), mobile AFP units near fields, and integration of gas/char valorization (heat/soil amendment) can improve economics and sustainability.
- Hydrogen sourcing and optimization: low‑carbon H2 supply and minimization of H2 consumption through catalyst and process design will determine lifecycle emissions and cost competitiveness.
- Real‑time control: implementation of rapid SIMDIS/FTIR‑PCA online sensors in hydrotreaters to adjust conditions according to catalyst aging and feed variability.
Conclusions
This work shows that continuous hydrotreatment of straw AFP bio‑oil over commercial sulfided NiMo/Al2O3 in a fixed bed can produce organic fractions compatible with refinery processing when sufficient severity is applied (notably 360 °C and 8 MPa). Key performance outcomes include retained energy >85% in the organic phase, TAN <2 mg KOH·g−1, water <1 wt%, low coking tendency, and complete miscibility with straight‑run gas oil for the best product. In addition, the study establishes practical rapid‑screening analytical approaches (SIMDIS recovery and FTIR‑PCA) useful for near‑real‑time process control. Remaining development needs focus on catalyst stability, hydrogen management and process integration for industrial deployment.
References
- Auersvald M., Shumeiko B., Vrtiška D., Straka P., Staš M., Šimáček P., Blažek J., Kubička D. Hydrotreatment of straw bio‑oil from ablative fast pyrolysis to produce suitable refinery intermediates. Fuel 238 (2019) 98–110.
Content was automatically generated from an orignal PDF document using AI and may contain inaccuracies.