<h4>Pre-Installation Checklist</h4><ul><li>Replace oxygen, moisture and hydrocarbon traps as necessary.</li><li>Check gas cylinder pressures to ensure that an adequate supply of carrier, make-up and fuel gases are available. Carrier gases should be of the highest purity.</li><li>Ensure that the injection port is clean and free of sample residues, septum, or capillary debris.</li><li>Check and replace as necessary critical injector components such as seals, liners, and septa.</li><li>Check and replace detector seals as necessary.</li><li>Carefully inspect your column for damage or breakage.</li></ul>Note: It is critical that oxygen and water be removed from the carrier gas by the appropriate use of filters and adsorbents<h4>Injector Installation</h4>Note: GC columns do not have a specific directional flow when received from the manufacturer. Upon initial use of your new GC column, it is recommended to dedicate one specific end of the column for injector installation only. This is particularly important when dealing with active/caustic or contaminating compounds. If these compounds are routinely injected onto the column, degradation of the phase will occur—leading to higher bleed. A typical first step to remedying (removing) this bleed would be to trim 10 cm from the front (injector) end of the column and keep trimming this inlet end of the column as necessary. Trying to remedy any bleed issues by trimming the column may not work if both ends have been interchangeably installed into the inlet.<ol><li>Place a capillary nut and ferrule on the injector end of the GC column, allowing a section of column to protrude. Trim one to two centimeters from the protruding end to remove ferrule contamination that may have entered the column. Inspect the cut with a magnifier to ensure that a smooth, clean, square-cut edge has been made - recut if necessary.</li><li>Carefully hang the column in the GC oven, being cautious not to scratch or damage the polyimide coating on the capillary tubing. Rotate the column to avoid sharp bends of the capillary column and any contact of the column with oven surfaces.</li><li>Insert the column into the injector exactly the correct distance specified in the instrument manual. Tighten the ferrule nut finger-tight then 1/2 turn with a wrench. If the column can still be moved, tighten another 1/4 turn until the column is secure.</li><li>Adjust the carrier gas to obtain the flow rate listed on the test chromatogram.</li></ol>

Gas Chromatography (GC) Column Installation - Injector Installation

When installing your capillary GC column, making accurate connections is essential to ensure trouble free operation. In this technical tip we provide advice on the best way to achieve this.<blockquote>Note: For users with sensitive detectors such as MS and ECD, column conditioning steps should be performed before installing the column to prevent contamination and frequent maintenance of the detector.</blockquote>1) Place the column nut and ferrule past the end of the column and cut a centimeter or two off the end of the column. Be sure that the ferrule is the right size and pointing in the correct direction. Inspect the cut with a magnifier and ensure that the cut is square and smooth. See figure below. Recut if needed.2) Insert the outlet end of the column into the detector exactly the distance prescribed in the instrument manual. Distances will vary between detectors. Tighten the ferrule nut finger-tight then 1/2 turn with a wrench. If the column can still be moved, tighten another 1/4 turn until the column is secure.3) Inspect the column connections for leaks using an electronic leak detector. Leaks at the inlet end may introduce oxygen to the column that will result in increased column bleed and damage to the column phase.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Gas_Chromatography_GC_Column_Installation_Detector_Installation_813b4d81a0.jpg" alt="Phenomenex: Gas Chromatography (GC) Column Installation - Detector Installation: Correctly and Incorrectly Cut GC Capillary." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Gas_Chromatography_GC_Column_Installation_Detector_Installation_813b4d81a0.jpg 245w," sizes="100vw" width="877" height="242">

Gas Chromatography (GC) Column Installation - Detector Installation

Article

Product

Events

Webinars

Application

Academy

Video

Poster

Scientists

Plastics

Environment

Food

Water

Health

Presentation

Scientific article

Interview

Toxicology

Popularization

Science and research

Software

Covid-19

Career

Laboratories

Various

PFAS 

Zaměření

Type of News

Focus

Phenomenex is a global technology leader committed to developing novel analytical chemistry solutions that solve the separation and purification challenges of researchers in industrial, government and academic laboratories.

Phenomenex

LNP Analysis by Light Scattering: A Waters | Wyatt User Meeting

LECO Training Course GDS900/950 & CDP

Thermo Fisher Scientific Analytical solutions forum

Validated Method for PFAS Testing in Food, Including Meats

Confidence in PFAS Data: Smarter Sample Prep, Contamination Control, Highly Sensitive and Robust MS

From sample to result: advanced sample prep strategies for food and environmental matrices